Newb Twin Turbo Mustang

[TT_05_Stang]

Sup everyone. Just found this site. I figured I would share my ride since I just finished putting it together, and Dyno tuned. The car is a handfull, and now I am starting to look into changing the suspension. Last night I took it out, and its a totally different feeling being able to lite the tires up at 85mph... Anyways enough talk here are some pics of the progress, and work I have done so far...

Car:
05 Mustang GT

Engine:
4.6
Alum Block
Manley Forged H-Beam Rods
Cobra Forged Crank
Stainless Ringset
9:1 Compression
Ported Heads
Stock Cams

Fuel:
Duel GT Supercar pumps
60# injectors
Full supporting fuel rails and feed lines

Transmission:
3650
26 splnie input shaft
Spec stage3+ LP option
RAM Adjustable T/O bearing
Upgrades syncronizers

Driveline:
Spydershaft alum driveshaft
Detroit TruTrac 31 spline axles
Rear End Girdle
355 rear end gears

Apperance:
GT500 front end
Steeda Cowl Hood
Ducktail Spoiler
I NEED RIMS!!!!! I am thinking on the Foose Nitrous in Grey Any Ideas????

Suspension
Torque Limiters
Upper and lower control arms

Power:
Pump Gas
15psi, 17* timing,
612rwhp 589rwtq on a Mustang Dyno

Pretty much stock, jsut some basic boltons when I purchased it.
http://img1.putfile.com/thumb/4/11220471290.jpg (http://www.putfile.com/pic/5294268)

Did some paint work, while saving for the turbo kit.
http://img2.putfile.com/thumb/9/25822052353.jpg (http://www.putfile.com/pic/6627150)

Purchased fuel rails and ran -8 feed from tank (duel GT supercar pumps)
http://img2.putfile.com/thumb/6/15923052298.jpg (http://www.putfile.com/pic/5642870)

http://img2.putfile.com/thumb/6/16015462425.jpg (http://www.putfile.com/pic/5647811)

I then purchased the twin turbo kit(i could have built one better...)
http://img2.putfile.com/thumb/9/24711100541.jpg (http://www.putfile.com/pic/6516994)
http://img2.putfile.com/thumb/9/24309331419.jpg (http://www.putfile.com/pic/6475135)
http://img2.putfile.com/thumb/9/24711100646.jpg (http://www.putfile.com/pic/6516995)

And after 12 hours of being tuned...
http://img2.putfile.com/thumb/12/36112120593.jpg (http://www.putfile.com/pic/7365807)
http://img2.putfile.com/thumb/12/36112120491.jpg (http://www.putfile.com/pic/7365798)
http://img2.putfile.com/thumb/12/36112120459.jpg (http://www.putfile.com/pic/7365799)
http://img2.putfile.com/thumb/12/36020460757.jpg (http://www.putfile.com/pic/7362426)
http://img2.putfile.com/thumb/12/36112120332.jpg (http://www.putfile.com/pic/7365794)
Ton more pics on the putfile site...

I then had the shortblock built by Proline I assembled the longblock
http://img2.putfile.com/thumb/4/11022395343.jpg (http://www.putfile.com/pic/8020287)
http://img2.putfile.com/thumb/4/11022395312.jpg (http://www.putfile.com/pic/8020286)
http://img2.putfile.com/thumb/5/14714180375.jpg (http://www.putfile.com/pic/8209252)
http://img2.putfile.com/thumb/5/14714180391.jpg (http://www.putfile.com/pic/8209251)

Installed a 26 spline input shaft in the 3650 made by Liberty Trans and installed a RAM adjustable T/O bearing Link to install here...
http://img2.putfile.com/thumb/7/19014414960.jpg (http://www.putfile.com/pic/8409272)

Now with the hood and GT500 front end on... yes I need to paint the intercooler brackets :)

http://img2.putfile.com/thumb/7/19014535337.jpg (http://www.putfile.com/pic/8409278)
http://img2.putfile.com/thumb/7/19014535329.jpg (http://www.putfile.com/pic/8409279)

There are a ton of pics on my putfile site, which everything is public so look around :biggthumpup:

[Josh99V6Stang]

nice