lucheski
08-15-2007, 02:05 AM
88 Mustang GT w/ 351W
$2600 for it all
This was a Project car I intended to Turbo. I am the third owner and the car is bone stock besides the exhaust. The car has
a "new to me" AOD tranny I got from a guy at Sextons Performance in GA. The tranny is installed but has not been tested since the car will not start (needs a fuel pump).
The car is stock besides the following:
NEW Summit Racing Off-road H-pipe
Flowmaster 40s
Also included with the car will be:
Fresh 351W shortblock
1979 Block D9AE Casting
.30 over
Hyperutectic Pistons
crank turned 10/10
351W EFI distributor
Unknown "Lunati" flat tappet cam and lifter
Engine Stand
Complete 5-lug conversion and brake upgrade (all you need is 5 lug axles) [SOLD]
-2 front aluminum PBR dual piston calipers with brake pads and rotors (from a 00GT) [SOLD]
-95GT Spindles and hubs [SOLD]
-2 GM (Cadillac) rear calipers with brake pads, rotors and custom mounting brackets for FOX 8.8 rear (mounting brackets cost me 150.00 bucks) [SOLD]
-instructions for how to put it all together.
Mass Air Conversion Kit
A9P Mass Air Computer
Complete (Uncut) Mass Air Harness w/ O2 and Injector harness
Cleaned and Oiled K&N Cone Filter
Stock MAF
Complete 8.8 w/ 3.55s from a 87GT Mustang
heady @ comcast.net
423-667-2657
http://img525.imageshack.us/img525/2838/img0547se5.jpg
http://img292.imageshack.us/img292/4637/9b1rq7.jpg
http://img125.imageshack.us/img125/7256/351wxz5.jpg
$2600 for it all
This was a Project car I intended to Turbo. I am the third owner and the car is bone stock besides the exhaust. The car has
a "new to me" AOD tranny I got from a guy at Sextons Performance in GA. The tranny is installed but has not been tested since the car will not start (needs a fuel pump).
The car is stock besides the following:
NEW Summit Racing Off-road H-pipe
Flowmaster 40s
Also included with the car will be:
Fresh 351W shortblock
1979 Block D9AE Casting
.30 over
Hyperutectic Pistons
crank turned 10/10
351W EFI distributor
Unknown "Lunati" flat tappet cam and lifter
Engine Stand
Complete 5-lug conversion and brake upgrade (all you need is 5 lug axles) [SOLD]
-2 front aluminum PBR dual piston calipers with brake pads and rotors (from a 00GT) [SOLD]
-95GT Spindles and hubs [SOLD]
-2 GM (Cadillac) rear calipers with brake pads, rotors and custom mounting brackets for FOX 8.8 rear (mounting brackets cost me 150.00 bucks) [SOLD]
-instructions for how to put it all together.
Mass Air Conversion Kit
A9P Mass Air Computer
Complete (Uncut) Mass Air Harness w/ O2 and Injector harness
Cleaned and Oiled K&N Cone Filter
Stock MAF
Complete 8.8 w/ 3.55s from a 87GT Mustang
heady @ comcast.net
423-667-2657
http://img525.imageshack.us/img525/2838/img0547se5.jpg
http://img292.imageshack.us/img292/4637/9b1rq7.jpg
http://img125.imageshack.us/img125/7256/351wxz5.jpg