wideopen
12-03-2007, 11:41 AM
1: Complete built zero balanced 306: 1989 block- decked, line hones, bored with torque plates to piston specs, new cam bearings, deburred, DSS main support, ARP main studs.Clevite 77 bearing through out.
Crank: Eagle 4340 steel crank, knife edged, lightened, oil holes chamfered, journals polished, Zero balanced-drilled with Mallory added, very nice crank.
Rods: Eagle ESP 3D H-beam rods with oversized ARP rod bolts. Improved oiling mod.
Pistons: BRC forged 10:1 to 1 nitrous pistons, for inline and TW heads, skirts have been dry film coated, tooled steel wrist pins, spiro locks, hellfire ring package.
Includes Pioneer SFI Zero balanced harmonic balancer and CIN-R-GY billet aluminum zero balanced flywheel. The complete assembly was balanced together by Panhandle performance.
Cam: Anderson Ford Motorsports N-71, New billet timing chain and gears.
Pushrods: Trickflow hardened.
Heads: Completely reworked 378 miles ago: Trickflow Twisted Wedge’ Surfaced, new bronze valve guides, new valves, 7/16” screw in rocker studs, new guide plates, Anderson Hi-Rev valve springs, ARP head bolts, Crane 1.6 roller rockers, Ford Racing tall polished aluminum valve covers.
Intake: Trickflow Trackheat.
EGR: Trickflow 70mm
Throttle body: Edelbrock 70mm
Distributor: Factory with MSD cap, rotor, plug wire holder. Motorsports Blue plug wires, autolite spark plugs. New water pump.
Oil Pump: Jegs Blue printed standard volume.
Oil pan: Moroso 7 quart, with dip stick.
Motor runs strong and sounds awesome. It only has 378 mile on it.
Reason for the sale is: I’m getting a Dart Block Proline 347 for X-mas.
Thanks, $3000
Kevin (770) 883-6867 kdanner@gerdauameristeel.com
2: Tremec TKOII Complete Trans setup:
Tremec TKOII 378 mile since total rebuild by Hanlon Motor Sports
Center force DFX 26 spline clutch, pressure plate and throw out bearing.
50 oz. flywheel
UPR Billet shifter, with billet knob.
31 spline out put yoke
Adjustable clutch cable
Will trade 5 speed pedal assm for your auto pedals
$1500
3: Anderson series 4 PMS
Includes everything needed to install and run. PMS computer, all wiring, hand held unit, series cable, 3 bar map sensor with wiring, owners manual. This is a plug and play unit. I also still have some time left on my free tunes from Rick Anderson. If you buy it and get me your information I can send it to Rick and get you a custom start tune. There is a bad pixel on the handheld screen, you can read it fine and it doesn’t effect the unit. Just want to be honest.
$550
4: Exhaust for a 87-93 coupe:
Ford racing stainless steel 1 5/8” shorty headers. There is good shape and are discolored the brown that they always turn. $100
BBK 2 ½” off road H-pipe in good shape has some discoloration. Also has a bung welded in for a wideband. It does have a plug incase you don’t have one. $75
Flowmaster two chamber catback with stainless steel 2 ½” tail pipes. This was a three chamber unit and I had a local shop install the two chambers. $135
MSD 6Al: In great shape with the easy plug in wiring harness. $100
MSD 87-93 5.0 Ditributor: MSD factory replacement billet distributor 378 miles on it. Still have original box and paperwork $175
BBK fuel pump: New in the box BBK 255 in tank fuel pump for 87-95 cars $70
BBK inline fuel pump: BBK external inline fuel pump like the T-rex 378 miles like new. Includes mounts wiring etc. $125
BBK Cold air kit: Chrome BBK cold air kit, Mounts the oversized air filter in the fender well. Has blue silicone connectors 378 miles like new. $100
Injectors and Mass air: FMS red top 30# injectors and matching ProM 77MM chrome bullet. $300
Radiator and fan: 1991 factory radiator, Black majic electric fan and 1994 overflow catch container, wiring etc. $100
Trickflow TFS-N5150 nitrous kit: Trick flow plate system for the track or streat heat intakes. Includes everything. Plate, lines, silonoids, jets, brackets, wiring, manual. Has had one bolt ran through it on old motor. $500
NX EFI mustang wet kit: NX single nozzle wet kit. Includes everything to install except some common electrical wire. Extra jets, shark nozzle, braided lines, micro switch, bottle & brackets, purge valve, etc. Had about 7 bottles ran through it. $375
Computer: A9P computer and wiring harness $125
Springs: One set of 4 cylinder front springs for a 87-93 coupe, these have been cut and look awesome on a V8 coupe with drag lites or 17” wheels. Also have a set of untouched 4 cyl front springs out of a coupe. $40 each
Power steering: Power steering pump and rack out of my 1991 coupe. $75
Vortech Blue FMU: Has the stainless steel braided lines $30
Crank: Eagle 4340 steel crank, knife edged, lightened, oil holes chamfered, journals polished, Zero balanced-drilled with Mallory added, very nice crank.
Rods: Eagle ESP 3D H-beam rods with oversized ARP rod bolts. Improved oiling mod.
Pistons: BRC forged 10:1 to 1 nitrous pistons, for inline and TW heads, skirts have been dry film coated, tooled steel wrist pins, spiro locks, hellfire ring package.
Includes Pioneer SFI Zero balanced harmonic balancer and CIN-R-GY billet aluminum zero balanced flywheel. The complete assembly was balanced together by Panhandle performance.
Cam: Anderson Ford Motorsports N-71, New billet timing chain and gears.
Pushrods: Trickflow hardened.
Heads: Completely reworked 378 miles ago: Trickflow Twisted Wedge’ Surfaced, new bronze valve guides, new valves, 7/16” screw in rocker studs, new guide plates, Anderson Hi-Rev valve springs, ARP head bolts, Crane 1.6 roller rockers, Ford Racing tall polished aluminum valve covers.
Intake: Trickflow Trackheat.
EGR: Trickflow 70mm
Throttle body: Edelbrock 70mm
Distributor: Factory with MSD cap, rotor, plug wire holder. Motorsports Blue plug wires, autolite spark plugs. New water pump.
Oil Pump: Jegs Blue printed standard volume.
Oil pan: Moroso 7 quart, with dip stick.
Motor runs strong and sounds awesome. It only has 378 mile on it.
Reason for the sale is: I’m getting a Dart Block Proline 347 for X-mas.
Thanks, $3000
Kevin (770) 883-6867 kdanner@gerdauameristeel.com
2: Tremec TKOII Complete Trans setup:
Tremec TKOII 378 mile since total rebuild by Hanlon Motor Sports
Center force DFX 26 spline clutch, pressure plate and throw out bearing.
50 oz. flywheel
UPR Billet shifter, with billet knob.
31 spline out put yoke
Adjustable clutch cable
Will trade 5 speed pedal assm for your auto pedals
$1500
3: Anderson series 4 PMS
Includes everything needed to install and run. PMS computer, all wiring, hand held unit, series cable, 3 bar map sensor with wiring, owners manual. This is a plug and play unit. I also still have some time left on my free tunes from Rick Anderson. If you buy it and get me your information I can send it to Rick and get you a custom start tune. There is a bad pixel on the handheld screen, you can read it fine and it doesn’t effect the unit. Just want to be honest.
$550
4: Exhaust for a 87-93 coupe:
Ford racing stainless steel 1 5/8” shorty headers. There is good shape and are discolored the brown that they always turn. $100
BBK 2 ½” off road H-pipe in good shape has some discoloration. Also has a bung welded in for a wideband. It does have a plug incase you don’t have one. $75
Flowmaster two chamber catback with stainless steel 2 ½” tail pipes. This was a three chamber unit and I had a local shop install the two chambers. $135
MSD 6Al: In great shape with the easy plug in wiring harness. $100
MSD 87-93 5.0 Ditributor: MSD factory replacement billet distributor 378 miles on it. Still have original box and paperwork $175
BBK fuel pump: New in the box BBK 255 in tank fuel pump for 87-95 cars $70
BBK inline fuel pump: BBK external inline fuel pump like the T-rex 378 miles like new. Includes mounts wiring etc. $125
BBK Cold air kit: Chrome BBK cold air kit, Mounts the oversized air filter in the fender well. Has blue silicone connectors 378 miles like new. $100
Injectors and Mass air: FMS red top 30# injectors and matching ProM 77MM chrome bullet. $300
Radiator and fan: 1991 factory radiator, Black majic electric fan and 1994 overflow catch container, wiring etc. $100
Trickflow TFS-N5150 nitrous kit: Trick flow plate system for the track or streat heat intakes. Includes everything. Plate, lines, silonoids, jets, brackets, wiring, manual. Has had one bolt ran through it on old motor. $500
NX EFI mustang wet kit: NX single nozzle wet kit. Includes everything to install except some common electrical wire. Extra jets, shark nozzle, braided lines, micro switch, bottle & brackets, purge valve, etc. Had about 7 bottles ran through it. $375
Computer: A9P computer and wiring harness $125
Springs: One set of 4 cylinder front springs for a 87-93 coupe, these have been cut and look awesome on a V8 coupe with drag lites or 17” wheels. Also have a set of untouched 4 cyl front springs out of a coupe. $40 each
Power steering: Power steering pump and rack out of my 1991 coupe. $75
Vortech Blue FMU: Has the stainless steel braided lines $30